©Westermo Teleindustri ABwww.westermo.comUser Guide6651-22641Industrial Converter Serial RS-485 to Fibre optic link Point-to-point applicationsODW-630
106651-22641System delay in an optical networkSerial data transferred from one ODW-630-F1 via an optical network to a second one, will be delayed due
116651-22641Status Port type Signal relay, changeover contactsRated voltage Up to 48 VDCOperating voltage Up to 60 VDCContact rating 500 mA @ 48 VDCCo
126651-22641FX (Fibre) SM-LC80 SM-LC40 SM-LC15 MM-LC2Fibre connector LC duplex LC duplex LC duplex LC duplexFibre type Singlemode 9/125 mmSinglemode 9
136651-22641Location of Interface ports, LED’s and DIP-switchesPosition Direction* Description Product marking1 In Common voltageCOM2 In Voltage A +VA
146651-22641LED indicators LED Status DescriptionPWR PowerON In service (power)Flashing Fault conditionOFF Out of serviceRDR OFF Not usedCH 2 OFF Not
156651-22641ConfigurationAll needed configurations and parameter settings are done by the DIP-switches, located under the top lid.!DIP-switch settings
166651-22641Factory settingsON 1 2 3 4 5 6 7 8S1ON 1 2 3 4 5 6 7 8S2S1 DIP-switchON 1 2 3 4 5 6 7 89 bits data formatON 1 2 3 4 5 6 7 810
176651-22641SW:1 SW:2Transmitter ONON 1 2 3 4 5 6 7 8ON 1 2 3 4 5 6 7 81.6 msON 1 2 3 4 5 6 7 8ON 1 2 3 4 5 6 7 8416 µsON 1 2 3 4 5 6 7
186651-22641RS-485 termination at system levelThe system should be installed in according to the RS-485 specification. A system should always form a
196651-22641CoolingThis unit uses convection cooling. To avoid obstructing the air-flow around the unit, use the following spacing rules. Minimum spac
26651-22641Legal informationThe contents of this document are provided “as is”. Except as required by applicable law, no warranties of any kind, eithe
206651-22641Configure the ODW-630-F1. …S1: 2-wire RS-485. Data rate, asynchronous mode must be set by S1. …S2: Asynchronous mode or Synchronous mode.
216651-22641HintsIf the distance is too long, it may be necessary to adjust the timing of the sender of the frame to allow acknowledgement of the rece
REV.A 6651-22641 2012-12 Westermo Teleindustri AB, Sweden – A Beijer Electronics Group CompanyWestermo • SE-640 40 Stora Sundby, SwedenTel +46 16
36651-22641SafetyBefore installation:Read this manual completely and gather all information on the unit. Make sure that you understand it fully. Check
46651-22641Note. Fibre Optic HandlingFibre optic equipment requires careful handling as the fibre components are very sensitive to dust and dirt. I
56651-22641Declaration of Conformity Westermo Teleindustri AB Declaration of conformity Org.nr/ Postadress/Postal address Tel. Telefax Pos
66651-22641Electromagnetic CompatibilityPhenomena Test Description LevelESD EN 61000-4-2 Enclosure contact ± 6 kVEnclosure air ± 8 kVRF field AM modu
76651-22641 STATUS C NO NC LED’s Switches CH 1 SFP Fibre transceiver TX RX Internal Electronics ODW-630-F1 COM COM +VA OVP +VB POWER T/R-
86651-22641Point-to-point communication via fibre optical network The serial data is transferred via a fibre optic network between two ODW-630-F1s. T
96651-22641Optical fibre link functionality and status indicationAt power on, all LED’s will be active during an initiation sequence followed by an au
Comments to this Manuals