©Westermo Teleindustri ABUser Guide6651-2201Industrial Converter PROFIBUS DP to Fibre Optic Link. Point to Point applicationswww.westermo.comODW-710-
106651-2201Functional descriptionConverter PROFIBUS DP – optical fibre ODW-710-F1 is a fibre optic modem that converts between electrical PROFIBUS DP
116651-2201Interface specifications* External supply current capability for proper startup PowerRated voltage ODW-710-F1: 12 to 48 VDC and 24 VAC
126651-2201PROFIBUS DP (RS-485)Electrical specification EIA RS-485 / EN 50 170Data rate 9 600 bit/s, 19.2, 93.75, 187.5, 500 kbit/s, 1.5, 3, 6 and 12
136651-2201Location of Interface ports, LED’s and DIP-switchesODW-710-F1Position Direction* Description Product marking1 In Common voltage COM2 In Vol
146651-2201LED IndicatorsLED Status DescriptionPWR PowerON Power is on.OFF Power is off.BA Bus activeON Data rate has been identified and data frames
156651-2201DIP-switch settingsBefore setting DIP-switches:Prevent damage to internal electronics from electrostatic discharges (ESD) by discharging y
166651-2201S1 DIP-switchS2 DIP-switchDescriptionON 1 2 3 4 5 6 7 8ON 1 2 3 4 5 6 7 81 faulty frame before data rate seen as unidentified*. S1: No
176651-2201Start up guideFollow the steps below to get the unit up and running in a simple application.… Use the factory DIP-switch settings.… Con
186651-2201LED indication under normal operationData from the PROFIBUS master is received at the ODW-710-F1 electrical port (as indi-cated by the DPR
196651-2201LED indication during optical link failureIf one fiber in the optical fibre pair fails, all cummunication with will be lost and the FL R LE
26651-2201Legal informationThe contents of this document are provided “as is”. Except as required by applicable law, no warranties of any kind, eithe
206651-2201Calculating system processing delayData exchange between a PROFIBUS DP master and slave via ODW-710-F1 fibre optic link, will be delayed du
216651-2201About the interfacesPower The power terminal has two independent inputs, +VA and +VB, allowing redundant power input. The ODW-710-F1 power
226651-2201About the automatic data rate detectionODW-710-F1 automatically detects the data rate by monitoring incoming PROFIBUS data frames on both t
236651-2201CoolingThis unit uses convection cooling. To avoid obstructing the air-flow around the unit, use the following spacing rules. Minimum spaci
REV.G 6651-2201 2014-10 Westermo Teleindustri AB, Sweden – A Beijer Electronics Group CompanyFor complete contact information, please visit our w
36651-2201SafetyBefore installation:Read this manual completely and gather all information on the unit. Make sure that you understand it fully. Chec
46651-2201Note. Fibre Optic HandlingFibre optic equipment requires careful handling as the fibre components are very sensitive to dust and dirt. If
56651-2201GeneralThis unit is intended for use in Zone 2 hazardous location only.Marking II 3 G Ex nA IIC T4 Gc SPECIAL CONDITIONWARNING – DO NOT
66651-22011234Position Descripton Input / Output values1 In & out / Relay contact (NO)Uin = 60 VDC maxIin = 500 mA max2 In & out / Relay conta
76651-2201SPECIAL CONDITION FOR SAFE USEAmbient temperature:This unit is designed for use in extreme ambient temperature conditions as follows: –40 ºC
86651-2201Declaration of Conformity Westermo Teleindustri AB Declaration of conformity Org.nr/ Postadress/Postal address Tel. Telefax Po
96651-2201Type tests and environmental conditionsElectromagnetic CompatibilityPhenomena Test Description LevelESD EN 61000-4-2 Enclosure contact ± 6
Comments to this Manuals