Westermo DDW-222 User Manual

Industrial Ethernet SHDSL extenderwww.westermo.comDDW-22212TXRXDSL©Westermo Teleindustri ABUser Guide6642-22203DDW-222 Wolverine series

106642-22203Type tests and environmental conditionsPhenomena Test Description Test levelsESD EN 61000-4-2 Enclosure contact ± 6 kVEnclosure air ± 8 k

116642-22203Description The DDW-222 is an Industrial Ethernet SHDSL extender with support for redundancy. The redundant protocol can be used ether on

126642-22203Interface specificationsPowerRated voltage 20 to 48 VDCOperating voltage 16 to 60 VDCRated current 300 mA @ 20 VDC 150 mA @ 48 VDCRated fr

136642-22203Ethernet TX Electrical specification IEEE std 802.3 2000 EditionData rate 10 Mbit/s, 100 Mbit/s, manual or autoDuplex Full or halfTransmis

146642-22203* Direction relative this unit** To minimise the risk of interference, a shielded cable is recommended when the cable is located inside

156642-22203LED indicators LED Status DescriptionPWR OFF No powerON (green) Booting ready, unit readyON (red) Unit is bootingFRNT OFF FRNT disabledON

166642-22203DDW-22212TXRXDSLDDW-22212TXRXDSLDDW-22212TXRXDSLDaisy chain SHDSL ConnectionRedundant SHDSL connectionThe DDW-222 are available with redun

176642-22203ConfigurationThe unit can easily be configured via the onboard Web based configuration tool. Local IP addresses can also be configured by

186642-22203By clicking the Scan for switches button the IP Configuration Software will detect the Westermo switches on the network. The software will

196642-22203The unit can be easily configured via the on-board Web based configuration tool. The network interface and switch properties can be confi

26642-22203Legal informationThe contents of this document are provided “as is”. Except as required by applicable law, no warranties of any kind, eithe

206642-22203Factory defaultIt is possible to set the unit to factory default settings by using two Ethernet cables and connect to the unit.To set the

216642-22203RemovalPress down the support at the back of the unit using a screwdriver. See figure.MountingThis unit should be mounted on 35 mm DIN-rai

REV.B 6642-22203 2011-12 Westermo Teleindustri AB, Sweden – A Beijer Electronics Group CompanyWestermo Teleindustri AB • SE-640 40 Stora Sundby,

36642-22203SafetyBefore installation:Read this manual completely and gather all information on the unit. Make sure that you understand it fully. Check

46642-22203WARNING – SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR DIVISION 2.WARNING – DO NOT OPEN WHEN ENERGIZED.WARNING – DO NOT DISCONNECT

56642-22203GeneralThis unit is intended to be used in Zone 2 hazardous location only.Marking II 3G Ex nA IIC T4 Gc SPECIAL CONDITIONWARNING – DO N

66642-22203Special condition for useAmbient temperature:This unit is designed for use in extreme ambient temperature conditions according to the follo

76642-22203RatingsPower (20 – 48) VDC; 300 mAAmbient temperature –40ºC ≤ Ta ≤ +70ºCIngress protection (IP) IP40Maximum surface temperature 135ºC (temp

86642-22203Agency approvals and standards complianceTypeApproved Agency/ W-moApproval / ComplianceEMC W-mo EN 61000-6-2, Immunity industrial environme

96642-22203Declaration of Conformity Westermo Teleindustri AB Declaration of conformity Org.nr/ Postadress/Postal address Tel. Telefax Post